top of page
ABCD Matrix

Photonic Crystal Waveguide

A photonic crystal waveguide (PCW, or PhC waveguide) is a channel that guides light by a line defect in a photonic crystal, rather than by ordinary total internal reflection alone.


A photonic crystal is a dielectric whose refractive index is periodic on the scale of the optical wavelength. That periodicity opens a photonic band gap (PBG): a range of frequencies for which no propagating Bloch modes exist in the crystal, so light in that band is reflected. Removing or resizing one row of the lattice (a line defect) pulls guided modes into the gap. Light at those frequencies cannot leak sideways into the crystal and is forced to travel along the defect.


How it is built:


The usual device is a two-dimensional photonic-crystal slab:


  • A thin high-index membrane (silicon, GaAs, InP, or similar) on a lower-index cladding or suspended in air.


  • A triangular (hexagonal) lattice of air holes etched through the slab. The lattice constant aaa is typically a few hundred nanometers for near-infrared light.


  • A W1 waveguide is formed by omitting one row of holes along a high-symmetry direction (often Γ–K). Omitting nnn rows gives a Wn guide.


Confinement is hybrid:


  • In the plane, by the photonic band gap of the surrounding lattice.


  • Vertically, by total internal reflection at the slab–cladding interfaces.


Three-dimensional crystals with a complete band gap can also host line-defect guides, but slab devices dominate because they are compatible with semiconductor fabrication.


Guided frequencies sit inside the gap of the perfect crystal. Only modes below the light line of the cladding are truly guided; modes above it can radiate out of the slab and are lossy.


Technical features:


The dispersion ω(k) of the defect mode is set by the hole size, lattice constant, and the geometry of the rows next to the channel. Near a band edge the slope flattens, so the group velocity:


vg=dω

       dk


becomes small. The group index ng=c/vg is often engineered in the range of about 10–50 over a useful bandwidth; higher values are possible but bandwidth shrinks and disorder loss rises. Dispersion engineering (shifting or resizing the first one or two rows of holes) is used to flatten ng​ over tens of nanometers.


Because the mode is excluded from the crystal by the band gap, bends of 60° or 90° can be low-loss on a scale of a few lattice periods—something index-guided wires cannot do. Mode areas are sub-wavelength, so the intensity for a given power is high. Propagation loss in good silicon W1 guides is typically a few dB/cm away from the band edge and rises roughly as n 2/g in the slow-light regime because of scattering from fabrication disorder.



Relation to lasers and photonics:


In lasers, the same lattice is used in two related ways. Closing a short section of line defect (for example an L3 cavity, three missing holes) makes a high-Q nanocavity; the surrounding crystal is the mirror, and the waveguide is the bus that couples light in and out. Photonic-crystal surface-emitting lasers use a 2D lattice for in-plane distributed feedback and coherent surface emission; the waveguide concept is the building block, but the device radiates vertically rather than guiding end-to-end.


Slow light in a PCW increases the effective interaction length, so gain, absorption, and nonlinearities are enhanced without a longer chip. That is used for compact modulators, amplifiers, and nonlinear sources that sit next to photonic-crystal or semiconductor lasers.



Applications:


  • Photonic integrated circuits: tight bends, splitters, couplers, and channel-drop filters on a footprint of tens of micrometers.


  • Slow-light delay and buffering, and shorter electro-optic or thermo-optic phase shifters, because the phase shift scales with ng​.


  • Nonlinear optics: four-wave mixing, harmonic generation, and photon-pair generation at lower power.


  • Sensing: the mode can overlap strongly with a gas or liquid in the holes, so small index changes shift the guided band.


  • Quantum photonics: a quantum dot or color center in or next to the waveguide couples efficiently to the guided mode, for single-photon sources and spin–photon interfaces.


  • Interconnects to photonic-crystal nanocavity lasers and filters.


A photonic crystal waveguide is a band-gap-confined line-defect guide. Its value in lasers and photonics is wavelength-scale routing, engineerable slow light, and strong light–matter interaction in a semiconductor platform.

bottom of page