top of page
ABCD Matrix

Non-Polarizing Beamsplitter

A non-polarizing beamsplitter (NPBS) is an optic that divides an incident laser or broadband beam into reflected and transmitted beams by optical power, while keeping the split nearly the same for s- and p-polarization. It is specified by a power ratio (for example 50:50 R:T), not by an extinction ratio.


That distinguishes it from a polarizing beamsplitter (PBS), which separates light by polarization state, and from a dichroic beamsplitter, which separates by wavelength.


Why “non-polarizing” is hard:


At oblique incidence, Fresnel reflection is stronger for s-polarization than for p-polarization, so a simple dielectric interface or an ordinary multilayer coating is strongly polarization-dependent. 


An NPBS coating is designed so that, over a stated wavelength band and angle of incidence,


∣Rs−Rp∣ and ∣Ts−Tp∣


stay small (often a few percent). The polarization state of the input is therefore approximately preserved in both outputs, and the split ratio does not swing with the input polarization.


Common coating approaches:


  • Hybrid metal–dielectric stacks (often with a thin silver layer) for broadband cubes. Polarization dependence is low, but the metal adds a few percent to about 10% absorption, so T+R<100.


  • All-dielectric multilayers for laser-line plates or cubes. Absorption is negligible, but the non-polarizing band is narrower.


  • Designs that combine interference with frustrated total internal reflection inside a cube for very flat Rs≈Rp​ over a visible band.


Forms:


  • Cube. Two right-angle prisms (typically N-BK7 or fused silica) are cemented or optically contacted, with the beamsplitter coating on one hypotenuse. Input is near normal to a face; the reflected beam exits at about 90°. Faces are usually AR-coated. A single internal reflection avoids the ghost reflections of a plate, and the optical path is equal in both arms if the cube is square. Cement limits pulsed or high-power use; optically contacted or air-spaced cubes are used when the adhesive would be damaged.


  • Plate. A flat substrate used at 45°, beamsplitter coating on the first surface and AR coating on the second. Lower dispersion and aberration than a cube for ultrafast beams, but the transmitted beam is laterally shifted and a residual second-surface reflection can produce a ghost unless the plate is wedged. Polka-dot (spatially patterned metal) plates are another broadband, polarization-insensitive option, at the cost of diffraction.


  • Typical commercial numbers for a 50:50 part (examples from Coherent, Newport, and Thorlabs datasheets): Rs≈Rp≈50%±5%, Ts≈Tp≈50%±5%, with ∣Rs−Rp∣ and ∣Ts−Tp∣ often within 5% or better at the design wavelength. Other ratios (10:90, 30:70, 70:30, 90:10) are common. Surface quality is often 40-20 or better, reflected-beam deviation a few arcminutes, and AOI tolerance about ±3∘.


Applications:


  • Sampling a laser for power monitoring or feedback without the sample depending on source polarization.


  • Splitting or combining beams in interferometers (Michelson, Mach–Zehnder) when both arms must keep the input polarization.


  • Fiber and telecom components (wavelength-selective switches, 40G/100G modules) where polarization-dependent loss must stay low.


  • Multi-path laser processing, pumping, and illumination.


  • Quantum optics, where a 50:50 NPBS routes single photons with a polarization-independent probability.


  • Low-dispersion plate NPBS versions in ultrafast experiments, where cube glass and cement would add group-delay dispersion and risk damage.


Selection trade-offs are bandwidth versus absorption, cube convenience versus plate dispersion and ghosts, and damage threshold (dielectric laser-line plates often rate around hundreds of W/cm² CW and ~0.5 J/cm² for 10 ns pulses at 1064 nm; hybrid metal cubes are lower). Match the coating to the laser line or band and to the actual angle of incidence; performance falls off outside the design window.

bottom of page