top of page
ABCD Matrix

Glass-to-Metal Seal

A glass-to-metal seal (GTMS) is a fused joint between glass and metal that forms a permanent, essentially impermeable barrier. In lasers and photonics it is the standard way to bring electrical pins, optical windows, or fiber through a metal package while keeping the interior hermetic.


The seal lets signals or light cross the wall of a vacuum-tight or gas-filled housing without a path for moisture, oxygen, or other contaminants. Laser diodes, photodiodes, and many fiber assemblies fail quickly if humidity reaches the facet, bond wires, or die attach, so the package leak rate is specified and checked (commonly by helium mass spectrometry, often to about 1×10−8 atm·cm³/s or tighter).


How the seal is made:


Glass is heated above its softening point so it wets an oxidized metal surface, then cools into a rigid insulator. Bonding is mainly chemical at the glass–oxide interface, sometimes reinforced by residual mechanical stress. 


Two design families are used:


  • Matched seal. Coefficients of thermal expansion (CTE) of glass, pin, and housing are kept close (often within about 10%). Strength comes from the chemical bond; residual stress stays low, so the part tolerates higher temperature and thermal cycling. The classic optoelectronics set is Kovar (Fe–Ni–Co) housing and pins with a borosilicate such as Corning 7052 or 7056. Sealing is typically done in air around 650–1000 °C so a controlled oxide forms on the Kovar.


  • Compression seal. The outer metal (often steel or stainless) has a higher CTE than the glass. On cooling it shrinks onto the glass and puts it in radial compression. Glass is strong in compression and weak in tension, so these seals handle higher pressure and mechanical shock. Pins are often Ni–Fe alloys (e.g. Alloy 52) with soda-lime, barium-alkali, or similar glasses. Common in rugged connectors and high-pressure feedthroughs; less dominant in precision laser headers because of residual stress and optical/electrical constraints.


Glass may be a preform bead, a frit paste, or a molded window. After sealing, headers are often plated (Ni/Au) for wire bonding and solderability.


Role in laser and photonic packages:


GTMS appears in three places:


  • Electrical feedthroughs (headers). A metal eyelet or base with glass-insulated pins. The laser or detector die is mounted on the header, bonds go to the pins, and a cap is resistance-welded or soldered on. The TO-can family (TO-18, TO-46, TO-56, and larger) is the volume form for edge-emitting lasers, VCSELs, and photodiodes. Multi-pin headers support monitor photodiodes, thermoelectric coolers, and thermistors in butterfly and other telecom packages.


  • Optical windows and lenses. A glass or sapphire window is sealed into a metal cap or flange so the beam exits a hermetic cavity. Used on TO-can window caps, LiDAR emitter/receiver packages, and high-power laser housings. The window can be AR-coated; flatness and tilt are controlled by fixturing during the seal.


  • Fiber feedthroughs. A fiber (often in a glass or ceramic ferrule) is sealed into a metal wall with sealing glass or a glass solder, sometimes as a compression seal so the housing keeps the joint under compression over the operating range. This is how pump modules and some transmitter packages get a hermetic fiber exit without relying only on epoxy, which is permeable over time.


Kovar is preferred next to GaAs, InP, and many ceramics because its CTE (about 555–666 ppm/°C) is closer to those materials than steel or copper, which limits stress on the die and on the seal during cool-down and operation.


Why it is used instead of epoxy or polymer seals:


Inorganic glass has near-zero permeability to water vapor and gases, so the internal atmosphere (dry air, nitrogen, or a controlled mix) stays stable for years. Epoxy and elastomer seals are fine for short-life or non-hermetic products; they are not used where Telcordia-style damp-heat and hermeticity requirements apply. Glass also provides high insulation resistance and voltage standoff in a small footprint, and it can be an optical element rather than only a dielectric.


Typical applications:


  • Telecom and datacom laser and photodetector packages (TO-cans, butterfly modules, pump lasers).


  • Automotive LiDAR emitter and detector housings.


  • High-power diode-laser bars and stacks that need a sealed window and electrical pins.


  • Fiber-coupled modules with hermetic fiber exits.


  • Medical and industrial laser handpieces and sensors that must survive autoclave, humidity, or pressure.


  • Related photonics hardware: hermetic connectors, sight glasses, and sensor headers in harsh environments.


Limits are process temperature (the seal cycle can damage temperature-sensitive organics or some coatings), CTE mismatch if the material set is wrong, and residual stress that can crack glass or shift optics. For those cases, designers use lower-temperature frits, glass-ceramics, or move to ceramic-to-metal seals when RF performance, higher pin density, or a different CTE match is required.

bottom of page